ACCESSORIES + POWER SUPPLIES
TRANSFORMERS
LOOK NO FURTHER! DEKOR™ “EZ” LED transformers are specially made to power 12 Volt DC LED light products - deck lighting, exterior lighting, indoor accent lighting - safely and reliably. Our high-performance, highly reliable LED power supplies are designed specifically for LEDs and low voltage DC lighting. The clean, constant and regulated 12 Volt DC output translates into high efficiency and better control over the evenness and brightness of connected LEDs. Using a high performance DEKOR™ LED transformer helps ensure that your LED light bulbs last their full lifetime.
TRANSFORMER HIGHLIGHTS
- long life LED transformers with an outstanding 3 year warranty
- 2 year warranty when used with non-DEKOR™ LED lighting products
- extremely clean and regulated 12 Volt DC output
- highly reliable with MBTF > 50,000 hours
- fully enclosed housings
- over voltage and thermal protection
- 3 waterproof models to choose from (36 watt, 60 watt, and 100 watt)
- compatible with all US and international power sources
- Energy efficient - DEKOR™ is an EnergyStar Partner
- Dimmable for long-term electricity cost savings using the DEKOR™ EZDIMMER
- Safety rated - ETL & C-ETL-US
- compact size for easy hiding • “EZ” to install and use
PLEASE NOTE: Using a DEKOR™ LED transformer allows us to provide you with our industry leading warranty on our LED lights. Conversely, DEKOR™ lights are designed to be used with DEKOR™ LED transformers and when another transformer is used in its place, this voids the LED warranty in its entirety.
EZ INDOOR POWER DRIVER
24 WATT LED POWER SUPPLY
PRODUCT ID: EZI24
Low voltage power driver for indoor use only
- compact profile
- 3 year warranty
Don’t let this transformer’s small size fool you -- it has all the same fault protection that our larger transformers have. Its smaller footprint is easy to hide, which is preferred with most indoor installations.
The wide range of input voltages and frequencies are compatible with all US and worldwide power sources. Designed to be used with DEKOR™’s remote dimmer or remote switch, or both.
SPECS
Input voltage: | 100-240 vac | Protection: | short circuit, overload, over voltage, thermal |
Input frequency: | 50/60 Hz | Dimensions: | 1.6” W x 1.1” H x 3.75” L |
Output current: | 2.0 amp | Cord: | 6’ 3-prong |
Output power: | 24 watt | Approvals: | CE, RoHS, ETL & C-ETL-US |
Output voltage: | 12 vdc regulated | MTBF (mean time between failure): | > 50,000 hours |
EZ 36 WATT LED POWER SUPPLY
PRODUCT ID: EZ36
- outdoor or indoor use
- waterproof (IP66) and impervious to the elements
- suitable for most projects
- 3 year warranty
The EZ Transformer is used in our outdoor light kits and sold separately to power all DEKOR™ lighted products. This transformer is our “workhorse” and will satisfy most project’s power needs.
The wide range of input voltages and frequencies are compatible with all US and worldwide power sources. Designed to be used with DEKOR™’s remote dimmer or remote switch, or both.
SPECS
Input voltage: | 100-240 vac | Input frequency: | 50/60 Hz |
Output current: | 2.5 amp | Output power: | 36 watt |
Output voltage: | 12 vdc regulated | Protection: | short circuit, overload, over voltage, thermal |
Dimensions: | 1.8” W x 1.7” H x 6.9” L | Cord: | 6’ 3-prong |
Approvals: | CE, RoHS, ETL & C-ETL-US | MTBF (mean time between failure): | > 50,000 hour |
EZ MAX 60 WATT LED POWER SUPPLY
PRODUCT ID: EZMAX60
- outdoor or indoor use
- waterproof (IP66) and impervious to the elements
- offers more power than E
- 3 year warranty
This transformer is for those larger projects or substantial wire runs requiring more power. Mounting is simple and effortless. The transformer is designed to be used with DEKOR™’s remote dimmer or remote switch or both. Input voltage allows for US and Canadian usage and other countries where 100 vac is used.
SPECS
Input voltage: | 120 vac | Input frequency: | 60 Hz |
Output current: | 5 amp | Output power: | 60 watt |
Output voltage: | 12 vdc regulated | Protection: | short circuit, overload, over voltage, thermal |
Dimensions: | 2.3” W x 2.6” H x 2.3” L | Approvals: | RoHS, ETL & C-ETL-US |
Power Rating: | Class II (U.L. 1585) | MTBF (mean time between failure): | > 50,000 hours |
EZMAXC LED TRANSFORMER
WATERPROOF 100 WATT 12V LED POWER SUPPLY
- contractor-grade Waterproof LED transformer, LED power driver
- for indoor or outdoor hard wire applications
This contractor-grade transformer is for those larger projects or substantial wire runs requiring more power, but still housed in a very small package. Mounting is simple and effortless. The transformer is designed to be used with DEKOR™’s remote dimmer or remote switch or both. Input voltage allows for US and Canadian usage and other countries where 100 vac is used.
SPECS
Input voltage: | 120 vac | Input frequency: | 60 Hz |
Output current: | 8.3 amp | Output power: | 100 watt |
Output voltage: | 12 vdc regulated with dual output leads | Protection: | short circuit, overload, over voltage, thermal |
Dimensions: | 2.8” W x 1.8” H x 9.8” L | Cord: | Input 3-conductor 1’ long, (2) output conductor 1’ long |
Approvals: | CE, RoHS, ETL & C-ETL-US | MTBF (mean time between failure): | > 30,000 hours |
LED CONTROLLERS: DIMMERS, SWITCHES AND TIMERS
LED Controllers from DEKOR™ are simply the top of the line and are specifically designed to our exacting standards for use with Dekor products. Our dimmers, switches and timers offer control and convenience. Create ambiance, save energy, increase the lifespan of your DEKOR™ LED lights. DEKOR™ is an ENERGYSTAR PARTNER.
All three of our controllers have been designed for ease of operation and to be used individually or together to give you the control and flexibility you desire.
PLEASE NOTE: These controllers are designed to be used with DEKOR™ LED transformers. When other transformers are used in place of DEKOR™ transformers, this voids the controller warranty in its entirety.
EZDimmer
WATERPROOF LED DIMMER & REMOTE
PRODUCT ID: EZ36
- waterproof housing and input/output connectors for outdoor use
- adjust color from base unit or using remote
- full control of light intensity
- remote-controlled
- 70 foot range (with new battery)
- teachable base unit in the event of remote loss
- higher input current can be used with any DEKOR transformer
- small footprint
- 1 year warranty
The EZ waterproof dimmer is designed to dim your project lighting and can be operated by either the included remote or by pressing the dimming buttons on the unit. The remote control has a range of 70 feet with replacement batteries readily available at most department stores.
This unit is designed for outdoor environments but can also be used with DEKOR™’s indoor lighting products where water is present (such as around or under a kitchen or bath sink).
This model has the ability to ‘teach’ a new remote in the event that an old remote is damaged or lost. This also allows for multiple remotes to be used at one location without interference.
Specs:
Input Voltage: | 120 vac | Dimensions: | W 2.0″ × H 1.1″ × L 3.8″ |
Input Frequency: | 60 Hz | Connectors: | Watertight twist lock |
Input/Output Current: | 10 amp (max) | Controls: | Dimming button, Brighten button, M? button |
Output voltage: | 12-0 vdc regulated | Approvals: | CE |
IP rating | 64 |
Remote Dimmer Specs:
Type: | Key Chain RF | Channel: | Single, self-programming |
Remote Range: | 70′ with antenna out and new battery | Control Range: | Zero - Full Intensity |
Battery: | 12v model 27a (included) |
EZTimer
PRODUCT ID: EZTIMER
- outdoor or indoor use
- photo-activated
- compatible with all DEKOR™ transformers
- 1 year warranty
The EZ Timer is designed to set the time you want to turn your project on or off. The unit is simple to install and program: simply plug the unit into an outlet, plug one of our transformers into it, and set the mode you want and you’re done!
Timer has the following program modes:
- off
- always on
- dusk to dawn
- on at dusk for 1-8 hours
Specs:
Input voltage: | 120 vdc | Output voltage: | 12 vdc at 8 amps |
Control: | remote | Controls: | rotary dial |
Mounting: | single screw mounting hole, mount unit vertically and at a minimum of 18” above ground level |
Approvals: ETL & C-ETL-US
EZSwitch
PRODUCT ID: EZ36
- Indoor or Outdoor
- Waterproof
- Impervious to the elements
- Remote controller
- 100 foot range
- 1 year warranty
The EZ Switch is designed to remotely turn your project on or off. The remote control has a range of 100 feet from the base unit with replacement batteries readily available at most department stores.
Wiring of the unit is simple: just attach the waterproof connector to one of DEKOR™’s transformer output leads and connect the output +/- wire leads to DEKOR™ lights.
Specs:
Input Voltage: | 120 vac | Dimensions: | W 2.3″ × H 2.8″ × L 2.3″ |
Input Frequency: | 60 Hz | Control: | Remote |
Output Current: | 5 amp | Approvals: | CE, RoHS, ETL & C-ETL-US |
Output voltage: | 12 vdc regulated |
Remote Switch Specs:
Type: | Key Chain RF | Channel: | Single |
Remote Range: | 100′ | Controls: | On button, Off button |
Battery: | 12v model 27a (included) |
EZ ENCLOSURE
HOUSING FOR TRANSFORMERS, TIMERS, ETC.
PRODUCT ID: EZENCL
- designed for outdoor use
- watertight design
- integrated lock hasp
- durable high-impact polycarbonate
- molded in bosses
- easy to remove lid
- smoke clear cover allows activation of photo cell
Keep your electrical components dry, clean up your installation with EZ ENCLOSURE. The enclosure is designed to house DEKOR™ LED transformers and controllers within a visually appealing housing. Made from durable polycarbonate, it can withstand the elements and is completely watertight -- this is important to protect your dimmer and timer, which are NOT waterproof. The NEMA unit is designed to be drilled and mounted as you see fit. Mounting bosses are located within the unit for mounting of components. Enclosure mounting tabs are included with each box.
SPECS
Dimensions: | 10.75” W x 13.5” L x 6.4” D | IP rating: | 67 (waterproof) |
Approvals: | UL both US and Canada, NEMA |
ACCESSORIES
CUSTOM FORSTNER BIT
PRODUCT ID: FB
This bit is custom ground to the specific diameter of .900 to allow a snug fit for our balusters, end caps, recessed lights, DEK dots and petite directional lights. Our bit is designed to produce up to 300 holes in yellow pine lumber, less in composite materials, and even fewer holes in materials such as Ipe (Epay) and Mahogany. Best to ensure that you have extra bits on hand!
DEKOR WIRE
PRODUCT ID: WIRE18
Our 18 gauge, outdoor-rated, UL-approved wire is the one and only wire we recommend for use with our illuminated systems. Sold in 100 ft spools.
INDOOR WIRE NUTS / OUTDOOR GEL-FILLED WIRE NUTS
PRODUCT ID: WIRENUTSM / WIRENUTSMGS
- UL approved
- packaged in quantities of 10
CUSTOM DRILL JIG
PRODUCT ID: DG
The drill jig is designed to fit over dimensional lumber (2x) on end. Simply drill your first hole, put the male brushing into the hole and use the opposite end drill bushing to drill your next hole. Using the jig will give you 4-5/8” on center for baluster installation and meets code for spacing. If your material is thinner than 2x or larger, just bend the side ears in until you have a nice fit on the material you are drilling.
DRILL KIT: JIG & BIT
PRODUCT ID: KIT
Our drill kit is a must-have for the serious installer and beginners, too. This kit includes both our custom drill jig and Forstner bit.